Holybro SiK Telemetry Radio V3 100mW 433MHz/100mW 915MHz

$56.47 USD

~~$0.00 USD~~ $56.47 USD

할인 품절

Color 100mW 433MHz 100mW 915MHz

재고 369개

Holybro SiK Telemetry Radio V3 100mW 433MHz/ 100mW 915MHz Open Source SIK Firmware Compatible Pixhawk Standard Flight Controllers For RC FPV Drone

Overview

This Holybro SiK Telemetry Radio is a small, light, and inexpensive open-source radio platform that typically allows ranges of better than 300m “out of the box” (the range can be extended to several kilometres with the use of a patch antenna on the ground). This radio is plug-n-play, ready for all Pixhawk Standard and other flight controllers, providing the easiest way to set up a telemetry connection between your Flight Controller and a ground station. It uses open-source firmware that has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Ardupilot, QGroundControl, PX4, and Flight Controller. The radios can be either 915 MHz or 433 MHz, and you should purchase the model that is appropriate for your country/region.

Features

Open-source SIK firmware
Plug-n-play for Pixhawk Standard Flight Controllers
The Easiest way to connect your Flight Controller and Ground Station
Interchangeable air and ground radio
Micro-USB port (Type-C Adapter Cable Included)
6-position JST-GH connector

Specifications

	SiK Telemetry Radio 100mW	SiK Telemetry Radio 500mW	SiK Telemetry Radio 1W
Max RF Power	20 dBm	27 dBm	30 dBm
Receive sensitivity	-121 dbm @2kbps RF Data Rate, -105 dbm @64kbps RF Data Rate
Antenna Gain	2dBi		5dBi
RF Data Rates	2, 4, 8, 16, 32, 64(default), 96, 128, 192, 250 kbps
Serial Interface Data Rate	1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6(default), 115.2 kbps
Frequency Band	902MHz - 928MHz or 414MHz - 460MHz
Interference Immunity	Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
Address Options	Network ID: 0 –255
Channels	Up to 50 Frequency Hopping Channels
Supported Network Topologies	Point-to-point
Configuration Method	MissionPlanner or AT Commands
Data Framing	Standard or MAVLink protocol framing
Error correction	Corrects up to 25% of bit errors with open-source SIK firmware
Serial Data Connector & Interface	6-pin JST-GH connector, 3.3V-TTL
USB	Micro-USB		Type-C
SMA Connector	RP-SMA female
Power Connector	NA		XT30
Operating Temperature	-40~85°C
Dimension	28 x 53 x 10.7mm (without antenna)		66.5 x 32 x 16.5mm (without antenna)
Weight	23.5g w/ antenna		67g w/ antenna
Input Voltage (DC)	5V		7~28V

2-way full-duplex communication through adaptive TDM UART interface
Transparent serial link
MAVLink protocol framing
Built in FT230X/FT23 USB to BASIC UART conversion IC

Electrical Data

Supply voltage:
- 100mW & 500mW version: 5V DC (from USB or JST-GH)
- 1W version: 7~28V DC via XT30
Transmit current: 100 mA at 20 dBm
Receive current: 25 mA
Serial interface: 3.3 V UART

FCC IDENTIFIER

2AP22-HT03-V3

Package Included

100mW & 500mW options
- Radio modules with antennas *2
- Micro-USB to USB-A cable *1
- Micro-USB to Micro-USB OTG adapter cable *1
- Micro USB to Type-C Adapter
- JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
- JST-GH-6P to Molex DF13 6P (for Pix32, Pixhawk 2.4.6, etc.)
Single 1W
- 1W Radio modules with antennas *1
- High-gain omnidirectional antenna *1
- Male Type-C to male Type-C USB cable *1
- Male XT30 to female XT30 adapter cable *1
- Male XT30 to female XT60 adapter cable *1
- JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
- Rubber damping grommet *3
Dual 1W
- 1W Radio modules with antennas *2
- High-gain omnidirectional antenna *2
- Male Type-C to male Type-C USB cable *1
- Male XT30 to female XT30 adapter cable *1
- Male XT30 to female XT60 adapter cable *1
- JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
- Rubber damping grommet *3